Can-Am Maverick X3 MAX 4-Door Upper Door Enclosure by SideXSide Enclosures

Can-Am Maverick X3 MAX 4-Door 2017-2026+ Upper Door Enclosure by SideXSide Enclosures

An X3 MAX moves fast enough that the open space above the doors turns into a wind tunnel, and this Can-Am Maverick X3 MAX upper door enclosure closes it off. The four panels work with the hard roof, windshield, and rear window already on your machine, so there is nothing else to buy. Heavy-duty ballistic material wraps the roll cage and runs across the top of each factory door, holding tight at speed. Make your attachment choice in the drop-down menu before you order.

Key Features

• Upper door panels for all four doors on the X3 MAX
• Heavy-duty ballistic material built to take wind, dust, and sun
• Works with the hard roof, windshield, and rear window already on the machine
• Wraparound attachment on the roll cage and across the top of each factory door
• Three attachment styles: self-adhesive Velcro, self-adhesive snaps, or pop-rivet snaps
• Velcro sewn along most of the panel so you pick the anchor points that work on your cage
• One-time setup runs under an hour, then a minute to remove or reinstall
• Everything needed for installation is included, along with a free storage bag
• Designed and sewn in Eastern Ohio, covered by a 1-year quality and workmanship warranty

Fitment

• Can-Am Maverick X3 MAX: 2017–2026+
• Four-door MAX models only

Important Fitment Notes

• MAX four-door machines only. The two-door Maverick X3 uses a different enclosure.
• Requires your factory hard roof, windshield, and rear window to be installed. This kit covers the upper doors only.
• No guarantee of adaptation with aftermarket accessories such as mirrors, light bars, or speakers.
• No guarantee is given on self-adhesive Velcro or self-adhesive snaps bonding to every surface. Pop-rivet snaps give the most positive hold, especially on a machine that sees high speeds.
• Velcro and self-adhesive snaps can damage decals if applied over them. Lay the panels out and mark placement before peeling any backing.
• Use short pieces of Velcro rather than one long strip — smaller sections bond better and stay put.
• Do not trailer the machine with the enclosure installed. Trailering voids the warranty.

Specifications

• Material: heavy-duty ballistic fabric
• Coverage: upper doors only, all four doors, sold as a set
• Vehicle fit: 2017–2026+ Can-Am Maverick X3 MAX, four-door
• Attachment: wraps around the roll cage and across the top of the factory door
• Attachment options: self-adhesive Velcro (no drilling), self-adhesive snaps (no drilling), or pop-rivet snaps (drilling required)
• Initial installation: under 1 hour
• Removal or reinstall after setup: about 1 minute
• Included: all installation hardware and a storage bag
• MPN: MavX3Max4DoorEnclosure
• Warranty: 1 year on quality and workmanship

Real Life Value and Uses

• Knock down the wind blast that comes with X3 speed on open desert and dune runs.
• Keep the dust cloud off the back seats when you are riding mid-pack in a group.
• Ride into the cold months without giving up the machine until spring.
• Stay dry when the weather turns partway through a long day out.
• Keep grit off your seats and dash so cleanup at the end of the day takes minutes.
• Strip all four panels off in about a minute when the season turns warm again.
• Store the set in the included bag instead of leaving it piled in the trailer.

Why Choose SideXSide Enclosures

• More than 30 years of canvas experience, building UTV enclosures since 2008
• Every pattern designed and sewn in Eastern Ohio
• Thousands of enclosures shipped to riders around the world
• Call in and you will usually reach the owner who designed it
• 1-year warranty on quality and workmanship, repaired or replaced at our discretion

Match your year to the fitment list, pick your attachment style, and get your X3 MAX closed in before the next cold run — call us if you want us to confirm your machine first.